Jump to content

Inony

Members
  • Content Count

    99
  • Joined

  • Last visited

  • Days Won

    9

Everything posted by Inony

  1. Installed to the body. The last step. Plug and Play !!! Finish
  2. Next is the Backpack section. It is the part I redesigned to be able to install VGA. I started with the Light Saber set first. This part has to be very careful. If the screw is too strong A beam from Light Saber may come out and cut off your hand. Then came the installation of a jet engine. Everything is installed in the steel structure. Testing the LED that it works fine. After that take VGA Come
  3. The next part is the body. Which has no hardware, but must be installed In order not to turn my work into a headless. I used a magnet to install it to make it easier to service the LED. Test the light for once. To take a picture for the forum update and then mount it on the base. I made it separate. To make it easier to work
  4. Bring both shoulders and attach them to the body part. To install the main hardware built-in When the hardware is installed, I run the test once to make sure everything is fine.
  5. When the torso is completed, then the shoulder. At this point, I designed it to accommodate a 120 mm radiator. But the hardware that I installed, I only use AIO, so I installed just a fan for beauty. No need to add more radiator After that, the part of the door was attached together. I used 4 magnets on each side to hold.
  6. The next step is to assemble the front door. Let's try to make sure everything goes smoothly. And it can be completely articulated. Bring the acrylic sheet to heat bending. And fixed. There are four magnetic sockets at this point on the main structure. And now everything is fine.
  7. After that, the body shell was installed. This shell at the bottom Can slide down a little for open the Back I / O connector on the back of the motherboard. I'll show you in the video that I'll upload when it's finished.
  8. After that, the next step is to install the PSU in the designed location. And take the final gear set to install in the designed position. This group is magnetic and has a socket support. it can be easily removed in - out When replacing PSU or cable management.
  9. The next step is to complete the installation of the hydraulic model. All the shock absorbers I designed are separate and can slide a little.
  10. When everything is fine, install the front panel next. After that, put the rest of the light boxes to install and test to make sure everything is fine.
  11. Let's start assembling from the base section first. I started with the rear end that was a light box. After fixing everything together, LED lights were installed and tested.
  12. When finished pasting the decals. We spray every pieces with a semi-matte lacquer. Now it's ready. For bringing all the piece to assemble
  13. The next step is the decal part. It is very difficult to get out of the house. And in my province don't have a water decal making shop. So I used a regular sticker and cut it with my machine. It is very difficult to paste because the letters are extremely small. But it's not my problem. I just cut it and send to my friend to paste it.
  14. Use the airbrush for shading to create shallow-depth that will make every pieces stand out more. Some points that need light to illuminate from the inside. With shapes that cannot be created with acrylic. We build them with resin print. Then coated with candy tone color The metal shad group was successfully painted.
  15. After doing the main color, the next step is draw lines. We're draw lines by hand on every piece. Some points that cannot be dragged through Use the brush Dip the paint to let the paint flow along the groove.
  16. When everything is fine Then take each part separately to color according to the main color. To prepare for the next step of airbrush and Decal. I will come back to update again. If the steps are not detailed Anyway, I'll add a video when it's done.
  17. After finishing the skin Then put each part together to check the last bug before applying the color.
  18. Finally, my friend was successful. With handling the surface of the workpiece Until I realize. When the drawings are completed in the set time of month, the number of parts is 200+ pieces. Fortunately, I don't have to be a scrub at all. The amount of it is a lot for work just 80cm. x 80cm. Thanks, mate!
  19. Exfoliating the skin smooth is tough for PETG filament. But my partner did it very well. This is his secret, how to get smooth skin. 1. Scrub the skin with a sandpaper. 2. Paint the skin with putty. 3. More scrub the skin with a sandpaper. 4. Paint the skin with more putty. 5. More and more scrub the skin with a sandpaper. Actually, I see two things over and over again. I feel very pity. So I decided to help him
  20. This contest I have 2 months to work before Final Submit.Together with the outbreak of COVID 19. There are lockdowns and curfews in my province. I had to trick my friends came to help. Become a special COVID-19 victims team. By dividing work together according to the aptitude of each person. In which I [Inony] will write all the 3D work and send files it to my friends [Suchao Modding] to print and scrub the surface then spray the main color. After that, take it to airprush to create Shading with his wife. The three of us have been friends for a long time. But never worked together
  21. When the primer has dried well, the Rivet Screw are installed. According to the designed point. Put all the pieces together. And measure again to check the fault point before assembling
  22. The main structure is constructed of steel sheet 1.5 mm thick and 2 mm thick. I don't have a plasma steel cutter, so I have to send my files to the factory. Seams and corner joints are always large. I have to come to check and edit every time So as not to be a problem in the process of assembling other enclosures. When fix every point is good, then apply a steel primer.
  23. The PSU is at the bottom center. When assembling and maintenance requirements. I designed it to just pull the shell around the magnetic mount. It is clear and easy for taking out or connecting wires. But in this case you have to take off ฺbackpack first. The back for placing the VGA is a magnetic cover like the other points. Next is the process of Build, painting and assembling. I will update again.
  24. The body is the main part where MB is installed. Below I designed the shell to move a little. To open the back I / O channel. It is for postponing the show when friends come home. Actually used, I made the front panel below. hahaha The cover of the case is designed to be easily pulled straight. Use a magnet to attach to the socket on the body. Hardware, I designed it to be installed on an external stand first. Then put inside
  25. Both shoulders The main structure is 1.5mm steel plate mounted with a 3Dprint magnetic socket At this point, I made it to support the installation of a fan or radiator a 120mm. Shell both at front and rear must removable, so it is very necessary. I actually wanted to design it to slide a little. But I only have one month to write it all. So I cut out the complexity.
×
×
  • Create New...

Important Information

By using this site, you agree to our We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue..