Rikuntyudady Posted September 27, 2012 Author Share Posted September 27, 2012 Hello,everyone. I made the LED illuminations for attaching to a front part this time. But I only made what was sold as a kit. It is an assembly in test. Since lighting was checked, wiring is extended so that it may be attached to a front portion. LED is attached to a reflector. A part removes easily by using a connector. The lighting test should look at the movie here.( ) I am sorry for explanation of Japanese. If a switch is pushed once, it will become the power supply ON. After a power supply is set to ON, whenever it pushes once, a lighting pattern changes. It will speed up, if it pushes twice. It will speed down, if it pushes three times. A power off if it pushes for a while. Thank you for seeing. I will report again in a few days. Link to comment Share on other sites More sharing options...
MonsterMawd Posted October 3, 2012 Share Posted October 3, 2012 lookin good dude! I love 922 case mods Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 4, 2012 Author Share Posted October 4, 2012 lookin good dude! I love 922 case mods Thank you for your comments!! I am proud when it says so. Link to comment Share on other sites More sharing options...
frozensnail Posted October 4, 2012 Share Posted October 4, 2012 looking good, like the acrylic work, are you going to illuminate some of the acrylic parts? Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 5, 2012 Author Share Posted October 5, 2012 looking good, like the acrylic work, are you going to illuminate some of the acrylic parts? Thak you for your comments. Yes. I am going to add LED to these. Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 13, 2012 Author Share Posted October 13, 2012 Hello,everyone. Work of me became busy. Work is seldom progressing. "LED Black hole" was manufactured in test this time. A tape LED and two half mirror type acrylic board is used. Usually, although it reflects like a mirror, it will become such if LED is turned ON. The black of the base color of tape LED is more desirable. The logo plate was put in. Since it is a mere test this time, whether it is used for HAF922 has not determined. (;￣ー￣A It is likely to become cool even if it puts into a 5.25-inch bay. Although it was a digression, I obtained a new case the other day. COSMOS 1000!!　♪ヽ(*´∀｀)ﾉ My friend found being sold for 5500 yen. (The delivery charge is also included in 5500 yen. ) The price of 5500 yen is about 70 dollars. It was cheap for the reason the outer packaging is crushed. The case itself is a new and it does not have a crack, either. It was very lucky. I would like to also begin MOD of this, when HAF922 and ATCS840 are completed. Incidentally I own 11 PC cases now. Six of them are a product of CoolerMaster. Thank you for seeing. I will report again in a few days. Link to comment Share on other sites More sharing options...
frozensnail Posted October 14, 2012 Share Posted October 14, 2012 The Cooler Master logo looks really cool in the mirror, very unique idea Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 14, 2012 Author Share Posted October 14, 2012 The Cooler Master logo looks really cool in the mirror, very unique idea Thank you for your comments. I think that the different effect will show up if the color of LED is changed or EL sheet is used instead of LED. Link to comment Share on other sites More sharing options...
Peter Brands Posted October 14, 2012 Share Posted October 14, 2012 Logo lookin awesome! (Same as the rest off course) Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 14, 2012 Author Share Posted October 14, 2012 Hello,everyone. This time, I did processing and paint of the side panel. "Bullet Hole" was drawn on the left side panel. The mesh portion is cut. An acrylic board is due to be attached here. A part of right side panel is cut off squarely. A transparent acrylic board is stuck from the back side. The milk white acrylics of 1mm thickness is attached to the front side, and a crevice is filled up with putty. A CoolerMaster logo is stuck after flattening with sandpaper. A logo portion is masked and the shadow portion of "Diamond Plate" effect is painted. I use two kinds of stencil sheets which I made by myself. Since the magnet sheet is cut and made, it sticks to a side panel. A shadow portion is painted by the pattern A and a highlight portion is painted by the pattern B. It is cautious of a position, the pattern A is put, and a highlight portion is painted. It becomes like this. â€Metal tears" effect is drawn. Masking is removed. (It has still left the portion of the logo.) If it illuminates by LED from an inner side after removing masking of the portion of a character, a logo portion will emit light. ♪ヽ(*´∀｀)ﾉ Moreover, in addition to "Bullet Hole", "Gun Smoke" was also due to be drawn also here, but there was no time today. I will report again in a few days. Thank you for seeing. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.