Rikuntyudady Posted October 14, 2012 Author Share Posted October 14, 2012 Logo lookin awesome! (Same as the rest off course) Thank you for your comments. Since it is not so difficult processing, please challenge. Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 16, 2012 Author Share Posted October 16, 2012 Hello,everyone. A bullet mark is added. Masking of a character is removed. If light is applied from the back side, it will become like this. The logo of CoolerMaster shines. "Gun smoke" effect is added. I will report again in a few days. Thank you for seeing. Link to comment Share on other sites More sharing options...
amdcrankitup Posted October 16, 2012 Share Posted October 16, 2012 This work log is nothing short of inspiring! keep up the good work Im definatly going to follow! Wow is all I can say! Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 17, 2012 Author Share Posted October 17, 2012 This work log is nothing short of inspiring! keep up the good work Im definatly going to follow! Wow is all I can say! Thak you for your comments!! I will do my best, warning against spoiling the original design of HAF922. Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 21, 2012 Author Share Posted October 21, 2012 Hello,everyone. The design of the side panel was completed mostly. The rest will be completion if topcoat is carried out. The surroundings of the design drawn the other day are left and masked. After painting silver, before drying, a hair line is drawn with a flat brush. Masking is removed once and a rivet is drawn on four corners. The effect of "Real Fire" is drawn. First of all, it draws roughly in a white. Candy red is put. Similarly, "white > candy orange > white > candy yellow" and a color are piled up. Woops...The daughter has been reflected. She cuts the hair of hair too much short, and seems to be a boy. The design of a side panel is completion now. 　♪ヽ(*´∀｀)ﾉ It waits for dryness, a urethane clear is painted, and it is finish. Then, the work of other parts is continued. I will report again in a few days. Thank you for seeing. Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 24, 2012 Author Share Posted October 24, 2012 Hello everyone. I did paint of a front part this time. A rivet effect is drawn for the whole after paint by Metallic dark grey . It masks with the label sheet which made the hole by pierce punch. An upper half is painted in a white and a lower half is painted black. Next, it masks with the round label sheet which remained in the pierce punch. As conversely as the point, an upper half is painted black and a lower half is painted in white. The surrounding dent of a rivet is reproduced. If the paint currently used is clear and is protected whenever it finishes one process since it is water, it can redo subsequent work. It can be wiped off at silicon-off etc. It is completion of a rivet effect. Finally, the part in a front part is painted with black. Although this is one part, two different parts seem to be stopped with the rivet. ♪ヽ(*´∀｀)ﾉ Finally, although it is the "LED black hole" introduced also to Facebook of CoolerMaster the other day, there is also a different method. A window is opened in the acrylics of 5-mm thickness, and it inserts from the half mirror type acrylics of two sheets. LED is installed in the edge portion of the acrylics of 5-mm thickness instead of an inside. Moreover, it becomes the different appearance. An interesting effect may be acquired even if it uses full color LED and LED with a motion. From now on, it is due to use it for ATCS840. http://forum.coolermaster.com/viewtopic.php?f=52&t=15661 I will report again in a few days. Thank you for seeing. Link to comment Share on other sites More sharing options...
oldman Posted October 24, 2012 Share Posted October 24, 2012 I can see that you are putting a lot of time and work in your project and it is worth it. It is just looking great! Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 25, 2012 Author Share Posted October 25, 2012 I can see that you are putting a lot of time and work in your project and it is worth it. It is just looking great! Thank you for your comments. Since I am doing work off the top of my head, without forming a precise plan, I require time for work. Link to comment Share on other sites More sharing options...
frozensnail Posted October 26, 2012 Share Posted October 26, 2012 The bullet hole, CM logo & paintwork are very well though out & applied to the case mod. Keep up the good work, really does look a good Link to comment Share on other sites More sharing options...
Rikuntyudady Posted October 26, 2012 Author Share Posted October 26, 2012 The bullet hole, CM logo & paintwork are very well though out & applied to the case mod. Keep up the good work, really does look a good Thank you for your comments!! Since work is slow, I am it worried whether it does on a deadline. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.