Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 Now an interesting step to you. The reservoirs aren't finish, because I don't have the oring for the upper and the lower part of them and the rest of the inox parts of them. But, I can make a mistake, I have not yet seen around rectangular water tank, and I like them very much. Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 The small panels of glass and aluminum profiles are fixed between them with transparent silicone, also placed inside in order to improve the seal. Once dried the silicone, I started to assemble the various panels of the structure in steel. Here I practiced another hole with screw and nut M4 to improve the tightness of the rear panel, since hosting the feeder suspended with respect to the bottom of the case, the weight of the latter is considerable. Here is the SSD mounted properly. After returning from vacation will complete all the reassembly of the panels. Will complete the trays so that they can fix and consequently also fix the support for the pumps Laing. From that point on, I will go to the study of the routes of pipes for the LCS and start an email to ... a famous manufacturer of fittings. See you soon! Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 Well even in this MOD could not miss. We welcome another sponsor! Corsair Italy has provided me with these fans SP120 High Performance PWM Edition. I thank Corsair Italy for the speed of response and shipment! And now, pictures! Small note. Note the base beneath the entire perimeter of the radiator in order to avoid that, by setting the fans, the screws may damage the raceways of the radiator itself. Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 And now...SLEEVE!!!! I buy Titanium Grey MKII e Grand Bleu for "normal" cable, and Grand Bleu for sata cable: all from MDPCx. Awesome. Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 I'm back! I promptly mounted the fans are coming from Corsair as a sponsor for the mod on both radiators. In a few days they come from three other PcHunter. Once the replacement of two radiators, I needed to place the trays and then the pumps in order to design a sketch LCS. Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 Construction water tank. My father has recovered rubber perfect for my reservoir, cut easily with a utility knife or scissors. Proceeds of the rectangular seals with the help of the cutter. The size is 60x55 mm, thickness 2 mm. Proceed with the widen the holes at the ends, going from M3 to M4, since the chopsticks that you'll see later I was able to retrieve only the M4, but I would say that is the most appropriate measure for my purpose. Here are the rods that act as braces to hold together the whole pan. Here I have devised a little trick to have the certainty and comfort to cut all 4 sticks perfectly. Cut made! Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 Here with the chain M4 thread chopsticks to be screwed a nut always M4. Final assembly with silicone seals directly on the glass. The seal rests on the piece of steel without being glued, however, so that if in the future I will need to open the pan for cleaning or any other type of intervention, it is feasible. See you soon with the twin gray! Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 Here the second!!! Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 Here them mounted!! Link to comment Share on other sites More sharing options...
Dave2010 Posted October 16, 2013 Author Share Posted October 16, 2013 And....A new sponsor!!! Very very nice to have it!!! Between few days, I'll receive all the items that I choose. The tubes that I'll use, are this below, that I show at the beginning of the mod. See you soon!! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.