Jump to content

NR200P addaptation for RTX 3080


 Share

Recommended Posts

  • 2 weeks later...
On 12/22/2020 at 4:35 AM, Andrey Bukhtiyarov said:

I tried 20mm and 25mm, thos heights displace PSU holder a little to front and cables from PSU became to close to front glass window. So, I selected height only 15mm.

Thanks for the explanation.

Ā 

I started receiving parts and began putting themĀ together. The two things that worries me the most are the clearance forĀ AIO cooler and RAM.

The Z53 AIO that I have is quite thickĀ with 52.4mm water block height and 30mm radiator height. I did a test fit and was able to stuck that in between the PSU holder and case. The side touchingĀ PSU holder cannot fit with protruding screws, so I left that unscrewed. I'm still looking into ways to secure the AIO cooler similar to yours.

I was able to close the top panel without cutting the extra plastics for included fans, but I might remove them purely for aesthetics.Ā 

Ā 

Once my motherboardĀ arrives, I will report further results later.

Ā 

Ā 

Link to comment
Share on other sites

  • 4 weeks later...
On 1/1/2021 at 4:24 AM, Xing said:

Thanks for the explanation.

Ā 

I started receiving parts and began putting themĀ together. The two things that worries me the most are the clearance forĀ AIO cooler and RAM.

The Z53 AIO that I have is quite thickĀ with 52.4mm water block height and 30mm radiator height. I did a test fit and was able to stuck that in between the PSU holder and case. The side touchingĀ PSU holder cannot fit with protruding screws, so I left that unscrewed. I'm still looking into ways to secure the AIO cooler similar to yours.

I was able to close the top panel without cutting the extra plastics for included fans, but I might remove them purely for aesthetics.Ā 

Ā 

Once my motherboardĀ arrives, I will report further results later.

Ā 

Ā 

Good day. I also have the Z53 as my AIO, so I'm definitely looking forward for your update. Wishing you all the best!

Link to comment
Share on other sites

  • 4 months later...
On 1/1/2021 at 4:24 AM, Xing said:

Thanks for the explanation.

Ā 

I started receiving parts and began putting themĀ together. The two things that worries me the most are the clearance forĀ AIO cooler and RAM.

The Z53 AIO that I have is quite thickĀ with 52.4mm water block height and 30mm radiator height. I did a test fit and was able to stuck that in between the PSU holder and case. The side touchingĀ PSU holder cannot fit with protruding screws, so I left that unscrewed. I'm still looking into ways to secure the AIO cooler similar to yours.

I was able to close the top panel without cutting the extra plastics for included fans, but I might remove them purely for aesthetics.Ā 

Ā 

Once my motherboardĀ arrives, I will report further results later.

Ā 

Ā 

Good day! Sorry for asking but I was just curious about your build. We have the same aio and I was also planning on doing this mod. Did you get around finishing it? Did the z53 fit inside the case? Hoping to get a response from you. Thanks!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...

Important Information

By using this site, you agree to our We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue..